XPS Thermal Insulation

Artherm Thermal Insulation Systems is economical, and prevents heat loss caused by the façade, thus saving heating and cooling cost by almost 50 percent.

It is the most ideal solution for the building as it covers the facade entirely. It prevents the formation of thermal bridges on the structural members such as columns, beams, etc.

Since it protects the building envelope against the heat exchanges, it prevents any negative effects on the load-bearing system.

It prevents any potential corrosion on the
reinforcements in the building load-bearing system.

It prevents condensation as well as the emergence of humidity, bacteria and
mould on the walls.

Since there will be no narrowing of the internal volume, the net floor area is not
affected.

It decreases the heating/cooling system installation costs in new buildings.

It decreases the façade maintenance costs of the building, and prolongs the life of the building.

In addition to energy saving in old buildings, it allows aesthetic solutions on the facades.

The sheathing system creates healthy and comfortable living conditions by ensuring balanced heat distribution. (According to the European Union standards, thermal comfort is the condition when the difference between
the interior temperature of the building and the surface temperature of the interior wall is no more than 2-3°C.)

EPS Thermal Insulation

All the advantages of a system

• Superior strength and durability.
  Designed to protect your building from any outside influence for decades.
• Energy saving.
  The most reliable investment with a guaranteed profit for the entire life of the building.
• Superior protection against moisture and mold.
  High water resistance and excellent breathability of the building ensuring walls without condensation and molds.
• Maximum protection from cracking.
  The most effective method of renovation on old facades that have cracks and other problems by providing maximum flexibility, strength and protection for several decades by reducing the contractions of components and cracked.

Marmox Board 50mm

Marmox Multiboard is a lightweight, high-performance tile backer board, used for waterproofing, dry-lining and thermal insulation,
offering the best long-term adhesion in its class. Marmox Multiboard consists of a core of extruded polystyrene bonded between
layers of fibreglass reinforced polymer concrete.
Thicknesses range from 4mm to 80mm allowing Marmox Multiboard to be used to provide a platform for tiling, a waterproof
barrier, thermal insulation on walls, floors and ceilings. Multiboard is easy to cut and shape providing freedom of design and quick
installation.

Marmox Board 30mm

Marmox Multiboard is a lightweight, high-performance tile backer board, used for waterproofing, dry-lining and thermal insulation,
offering the best long-term adhesion in its class. Marmox Multiboard consists of a core of extruded polystyrene bonded between
layers of fibreglass reinforced polymer concrete.
Thicknesses range from 4mm to 80mm allowing Marmox Multiboard to be used to provide a platform for tiling, a waterproof
barrier, thermal insulation on walls, floors and ceilings. Multiboard is easy to cut and shape providing freedom of design and quick
installation.

Marmox Board 10mm

Marmox Multiboard is a lightweight, high-performance tile backer board, used for waterproofing, dry-lining and thermal insulation,
offering the best long-term adhesion in its class. Marmox Multiboard consists of a core of extruded polystyrene bonded between
layers of fibreglass reinforced polymer concrete.
Thicknesses range from 4mm to 80mm allowing Marmox Multiboard to be used to provide a platform for tiling, a waterproof
barrier, thermal insulation on walls, floors and ceilings. Multiboard is easy to cut and shape providing freedom of design and quick
installation.

Marmox Board 6mm

Marmox Multiboard is a lightweight, high-performance tile backer board, used for waterproofing, dry-lining and thermal insulation,
offering the best long-term adhesion in its class. Marmox Multiboard consists of a core of extruded polystyrene bonded between
layers of fibreglass reinforced polymer concrete.
Thicknesses range from 4mm to 80mm allowing Marmox Multiboard to be used to provide a platform for tiling, a waterproof
barrier, thermal insulation on walls, floors and ceilings. Multiboard is easy to cut and shape providing freedom of design and quick
installation.

Buffa Coper Gum Liquid Membrane 20KG

Ready to use liquid membrane, flexible, semi-trafficable, for waterproofing flat or pitched roofs, terraces, balconies, concrete, etc. Apply Giunto Bond, Angolare B10 and Angolare B11 beforehand. Can be reinforced with Rete PB Fine coated mesh or Velo Vita.

• Apply with brush or roller.

Buffa Internal Paint 14L

Emulsion paint, ultra breathable, semi-washable, high hiding power, eco-friendly, ideal for bathrooms and kitchens. For indoor use.

• Visual effect: smooth matte finish.
• As base coat, use Presto primer.
• Apply with brush, roller or spray.

Buffa Ancorante BH

Anchoring membrane, resistant to damp, specially formulated for fixing Giunto Bond and Angolare B10/B11 waterproof accessories on roofs and terraces, and in showers, pools and foundations.

• Apply with stainless steel trowel or brush.

Buffa Bond LT51

Specific additive designed to improve bonding and flexibility of technical mortars, scratch coats, plasters, skim coats and screeds. Increases adhesion to substrates, improves flexibility properties, reduces water absorption. Ideal also for fresh on fresh work, and as grout for concrete construction joints.

• Use instead of gauging water.

Buffa Peg 600 Surface Impregnator

Breathable solvent.-based barrier coat formulated with siloxanes. Guarantees water-repellent and protective barrier for plasters, cotto, natural stone and fair-faced concrete. Ideal for restoration work and as protection for Buffa mineral finish coats. For indoor and outdoor use.

• Apply evenly with brush, roller or spray.

Buffa Viduest

Solvent-based protective stabilizing primer with high penetrating power, used as preparation for finish coats, including plastic resins, paints, liquid membranes, and Coper Max encapsulant for asbestos cement. Optimum as impregnant for plasters, fair-­faced stone and concrete, wet look. For outdoor use.

• Dilute first coat with Diluente 200.500 thinner at a rate of 20 to 30%, depending on the substrate.
• Apply with brush, roller or spray.

Buffa Max Etil

Deep penetrating protective stabilizer, ready to use, formulated with modified silicates. Ideal for application to surfaces such as powdery plasters and eroded substrates, and for treating mineral coatings affected by efflorescence. For indoor and outdoor use.

• Apply with brush, roller or spray.

Buffa Morex Rust Converter

Rust converter, designed to convert iron oxides into stable phosphates. Ideal for reinforcement rods.

• Apply with brush.

Buffa Vita Net

Acid-based cleaning fluid for removing traces of cement and lime. Suitable for clean-up operations after laying and fixing tiles, cotto, marble, etc.

• Dilute with water according to substrate.
• Apply with brush or sponge.

Untitled

Premixed mineral skim coat, superior technology, breathable, good filler, high quality. Ideal for use on Buffa Intonaco T70, Intonaco Rais, etc., and on traditional plasters, for skimming new and non-absorbent walls, even if slightly uneven. Suitable as a surface for coloured finishes, following preparation with appropriate primers, such as silicate, siloxane and acrylic coatings. Can be reinforced with Rete PB coated mesh. Intended for use as skim coat, or as finish coat if protected with Peg 600.
For indoor and outdoor use.

• Maximum grain size: 1.2 mm.
• Apply with smooth stainless steel trowel and finish with sponge float or plastic float.

Buffa Calcite Malta Colour

Premixed and coloured mortar formulated with natural hydraulic lime (NHL 3.5), breathable. Particularly suitable for pointing fair faced stone claddings and as bedding mortar for walls built of tufa block, stone, etc. Ideal for restoration work. For indoor and outdoor use.

• Maximum grain size: 1.2 mm.
• Apply with trowel.

Buffa Finitura Libeccio

Premixed mineral plaster replicating old-style sand-finishes, superior quality, superfine, breathable, formulated with hydraulic binders and marble powders. For indoor use.

• As base coat, use Intonaco Libeccio, Intonaco Libeccio Rocca, Intonaco Libeccio Rocca BS or Intonaco Libeccio Rocca Fibrato, after applying one coat of Tonachino Libeccio.
• Maximum grain size: 0.2 mm.
• Apply with smooth stainless steel trowel.

Buffa Coper Evoluzione

Ready to use one-part paste membrane, innovative, water-based, good filling power and strong bond with substrate, waterproof, semi-trafficable and highly flexible. Ideal for bathrooms, terraces, balconies, pools, basements before laying and fixing floor and wall tiles, natural stone and mosaic. Also suitable for wood or sheet metal roofing, and foundations. Apply Giunto Bond, Angolare B10 and Angolare B11 beforehand. Can be reinforced with Rete PB e Rete PB Fine coated mesh or Velo Vita, embedded in first coat.

Buffa T70 Cement Based Render

FEATURES

INTONACO T 70, premixed with a cement and aggregate base, for indoors and
outdoors. To be applied on pumice stone, tuff, bricks, stones, and cement.
The high resistance and breathability features make it ideal for mineral finishes
with a lime, silicate and siloxane base as well as heavy coatings with natural stone and ceramics.

Buffa Koboss

FEATURES

KOBOSS is a premixed microporous, dehumidifying, anti-salt, fiber-reinforced, transpiring, pearl gray, coarse-grained skimming plaster, studied in the context of specific low-thickness remediation cycles against rising dampness without the need to demolish, for masonry and concrete. For indoors and outdoors.

Buffa Top Elast Fibro Membrane

FEATURES

TOP ELAST FIBRO is an elastomeric, waterproof, fiber-reinforced acrylic smoothing compound, ready in paste, gray in color, filler, ideal for waterproofing bathrooms, showers, and kitchens, even on plasterboard, pitched roofs, balconies, terraces, exposed walls, etc.

Buffa Coper Cem Cement Membrane (A+B)

COPER CEM FLEX 2C BrochureFEATURES

COPER CEM FLEX 2C is a two-component, high-tech, high-strength, flexible, grey-colored, fiber-reinforced cementitious sheath based on cement, selected aggregates, and synthetic polymers in aqueous dispersion. By mixing only the two components A (powder) and B (liquid), a flexible, trawlable, highly resistant mixture is obtained, which can also be applied vertically up to 1 – 2 mm thick in a single coat.

Once hardened, COPER CEM FLEX 2C becomes an elastic sheath, very resistant and waterproof, on which it is possible to apply suitable adhesives such as DURAFLEX or DURAFLEX IMPER directly on top for subsequent flooring or our special elastic and waterproof white or colored such as COPER PAINT, COPER PAINT PLUS, COPER PAINT FINISH AS, COPER THERM, COPER GUM, ANCORANTE BH, etc. for its UV protection if the sheath remains visible.

COPER CEM FLEX 2C is provided with the following packages: 4 kg (3 kg component A + 1 lt component B), 16 kg (12 kg component A + 4 lt component B) and 32 kg (24 kg component A + 8 lt component B).